Altana Haze-Gard Plus Operating Instructions Uživatelský manuál Strana 17
- Strana / 180
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
State-of-the-art technology and the
reference-beam principle mean that
calibration is needed only infrequently.
We recommend a calibration interval
of two months.
Calibration is also necessary:
s ATTHElRSTSTARTUP
s INTHEEVENTOFADRASTICCHANGEIN
ambient temperature (for example,
after moving the unit to a new site)
s IF0LEASE2ECALIBRATEAPPEARS
on the display (for example, after
stored calibration values have been
modified).
To ensure accurate calibration, use
only original standards from
BYK-Gardner.
Do not touch the reference surface.
Protect it against scratching.
Even with careful treatment, ambient
conditions may alter a standard’s va-
lues over time. For that reason, have
Customer Service check your stan-
dards regularly (once a year) against
primary standards.
Make sure the values displayed du-
ring calibration match the data for the
standards you use, in order to avoid
mixing up or accidentally changing
the calibration values (see Section
5.3).
To calibrate:
CAUTION: Make sure the
calibration standards are clean
and free from scratches!
5. Calibration
- Cat.No. AT-4725 and AT-4726 4
- Table of Contents 4
- 1. Safety Information 6
- 2. System Description 8
- 3. Startup 9
- Setting Up 10
- Power-Up 11
- 4. Operation 14
- 5. Calibration 17
- Monitoring Test Equipment 20
- 5.2 Cleaning the Standards 20
- 5.4 Calibration with Taber 21
- Abrasion Holder 21
- Change Cal Value 22
- Input Trans Std 22
- Input Clarity Std 22
- Save Std Values 22
- 6. SET-UP Menu: Setting 23
- Instrument Parameters 23
- deleted 27
- 9. Parameters 30
- 10. Changing Lamps and 34
- 11. Interface Description 36
- 12. Technical Specifications 39
- 13. Ordering Guide 41
- Printer 42
- not ready 42
- Invalid date 43
- Memory 43
- full 43
- Cal values are 44
- set to default 44
- Online Mode 44
- Keyboard inactive 44
- Best.-Nr. AT-4725 46
- Best.-Nr. AT-4726 46
- Best.Nr. AT-4725 und AT-4726 48
- Inhaltsverzeichnis 48
- 1. Sicherheitshinweise 50
- 2. Systembeschreibung 52
- 3. Inbetriebnahme 53
- Aufstellung 54
- Version: 1.0 55
- Copyright 1994 55
- 4. Handhabung 58
- 5. Kalibration 61
- 5.1 Zusatzstandards zur 64
- Prüfmittelüberwachung 64
- 5.2 Reinigung der Standards 64
- 5.3 Kalibrierwerte ändern 65
- Kalibrierstd. ändern 66
- Transmission Std 66
- Clarity Standard 66
- Werte sichern 66
- Abbruch: SET UP 66
- STATISTIK n= 5 69
- 9. Die Meßgrößen 74
- 10. Lampen- und 78
- Sicherungswechsel 78
- 12. Technische Daten 83
- 13. Lieferhinweise 85
- Drucker 86
- nicht bereit 86
- Ungültige 87
- Datumseingabe 87
- Statistikspeicher 87
- ist voll 87
- Kalibrierdaten 88
- werden berichtigt 88
- Online Modus 88
- Tastatur gesperrt 88
- N° Réf. AT-4725 90
- N° Réf. AT-4726 90
- N°Réf. AT-4725 et AT-4726 92
- Table des matières 92
- 1. Consignes de sécurité 94
- 2. Description du système 96
- 3. Démarrage 97
- Installation 98
- Mise sous tension 99
- Std.transmission 100
- Standard clarity 100
- PRECHAUFFAGE 101
- 4. Fonctionnement 102
- 5. Etalonnage 105
- porte de haze 106
- Pret: OPERATE 106
- ETALONNAGE 106
- Mesure du 100% 106
- svp decouvrir la 106
- 5.1 Etalons supplémentaires 108
- 5.2 Nettoyage des étalons 108
- 5.3 Modification des valeurs 109
- Changer Etalonnage 110
- Du transm.std 110
- Du clarity std 110
- Enregistre Valeur 110
- Quitter: SET UP 110
- 6. Menu "SET-UP“: 111
- Sélection des 111
- paramètres de 111
- l’instrument 111
- 7. Mesures en série et 113
- statistiques 113
- 8. Mode continu 116
- 9. Les grandeurs de 118
- mesure 118
- 10. Changement des 122
- lampes et des fusibles 122
- 12. Données techniques 127
- 13. Liste des 129
- composants 129
- et accessoires 129
- 14. Messages d’erreur 130
- Memoire statistique 131
- pleine 131
- Valeurs de lʻetalon 132
- Mode Online 132
- clavier bloque 132
- No di cat. AT-4725 134
- No di cat. AT-4726 134
- No. di cat. AT-4725 e AT-4726 136
- 1. Informazioni sulla 138
- sicurezza 138
- 2. Descrizione del 140
- sistema 140
- 3. Inizializzazione 141
- Impostazioni 142
- Accensione 143
- Standard di trasmittanza 144
- Standard di clarity 144
- MEMORIA STATISTICA 144
- RISCALDAMENTO 145
- 4. Funzionamento 146
- 5. Taratura 149
- 5.1 Standard supplementari 152
- 5.2 Pulizia degli standard 152
- 5.3 Modifica dei valori 153
- Standard di 154
- Confermare: OPERATE 154
- Escape: SET UP 154
- 6. Menu SET-UP: 155
- Impostazione dei 155
- parametri dello 155
- strumento 155
- STATISTIC n= 5 157
- H 30.6 m= 30.1 157
- s= 0.5 157
- C 20.8 m= 20.3 157
- s= 0.4 157
- Eseguire la 161
- 9. Parametri 162
- 10. Sostituzione di 166
- lampade e fusibili 166
- 12. Dati tecnici 171
- 13. Guida agli Ordini 173
- Data non valida 175
- Misurazione di 175
- Memoria piena 175
- Valori di taratura 176
- Modalità in Linea 176
- Tastiera inattiva 176
- EG - Konformitätserklärung 177
- 238 013 796 EDFI 0805 180
Související produkty a manuály pro Měřící nástroje Altana Haze-Gard Plus Operating Instructions
(2 stránky)
(40 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce