Altana Haze-Gloss Manual Uživatelský manuál Strana 21
- Strana / 128
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
• Best results can only be obtained
from plane surfaces.
• Since gloss properties are usually not
constant over the complete sample
surface, the reflectometer value
should be determined on several
different locations of the sample and
the readings should be averaged.
• If a sample surface is structured, i.e.
the gloss porperties are dependent
on the measuring direction, it is
recommended to report the structure
characteristics and the angle of
incidence or to calculate the mean
value from readings taken in varying
directions.
• Samples that have to be measured
several times during a test (e.g.
weathering samples) should be
marked correspondingly in order to
make sure that comparison
measurements or check tests will be
performed on the same location.
Haze Measurement provides:
• better differentiation of optical
properties for high gloss surfaces
• an indirect method to evaluate and
characterize paint and raw material
properties, such as
- degree of dispersion
- flocculation behavior
- wetting properties
- scratch resistance
- weathering tests
- optimization of paint formulae
• an indirect method to evaluate the
manufacturing process of the surface.
Haze Measuring
• press haze key
If haze compensation: off was
selected in the Set Up Menu, "nc."
(= not compensated) appears in the
upper left corner of the display.
In many cases, the reflectometer value
does not suffice to describe the optical
properties of a surface. In addition to
color and gloss, reflection haze is of
great importance.
Haze
nc.
13.7
20°
86.5
haze
• Best results can only be obtained
from plane surfaces.
• Since gloss properties are usually not
constant over the complete sample
surface, the reflectometer value
should be determined on several
different locations of the sample and
the readings should be averaged.
• If a sample surface is structured, i.e.
the gloss porperties are dependent
on the measuring direction, it is
recommended to report the structure
characteristics and the angle of
incidence or to calculate the mean
value from readings taken in varying
directions.
• Samples that have to be measured
several times during a test (e.g.
weathering samples) should be
marked correspondingly in order to
make sure that comparison
measurements or check tests will be
performed on the same location.
Haze Measurement provides:
• better differentiation of optical
properties for high gloss surfaces
• an indirect method to evaluate and
characterize paint and raw material
properties, such as
- degree of dispersion
- flocculation behavior
- wetting properties
- scratch resistance
- weathering tests
- optimization of paint formulae
• an indirect method to evaluate the
manufacturing process of the surface.
Haze Measuring
• press haze key
If haze compensation: off was
selected in the Set Up Menu, "nc."
(= not compensated) appears in the
upper left corner of the display.
In many cases, the reflectometer value
does not suffice to describe the optical
properties of a surface. In addition to
color and gloss, reflection haze is of
great importance.
Haze
nc.
13.7
20°
86.5
haze
- Reectometer 4
- Cat.No. AG-4601 4
- Version: 2.6 5
- Copyright 1990 5
- 1. Safety Information 6
- 2. System Description 7
- 3. Start-Up 8
- 220-240 V 9
- Version: 2 10
- Copyright 1990 10
- 4. Operation 12
- 5. Calibration 13
- 7. Practical Measuring 19
- Hints 19
- 8. Measurement Series 23
- and Statistic 23
- 9. International 25
- Specifications 25
- 10. Interface Description 26
- 11. Technical Data 28
- 12. Sources of Errors 29
- 20° Lamp defect ! 30
- Continue: 30
- 13. Ordering Guide 31
- Reektometer 34
- Best.-Nr. AG-4601 34
- Gesamtansicht 37
- 1. Sicherheitshinweise 38
- 3. Inbetriebnahme 40
- 4. Handhabung 44
- HAZEKALIBRATION 47
- Hazekalibration ok 47
- 6. Einstellen der 49
- Geräteparameter 49
- SET-UP Menü 49
- 7. Meßpraxis 51
- 9. Normen 57
- 10. Schnittstellen 58
- beschreibung 58
- 11 . Technische Daten 60
- 12. Fehlerquellen 61
- 20° Lampe defekt ! 62
- 13. Lieferhinweise 63
- Brillancemètre 66
- N° Ref. AG-4601 66
- 1. Description du 70
- système 70
- 2. Démarrage 71
- Installation 72
- Version: 2.95 73
- Copyright 1991 73
- 3. Fonctionnement 75
- ETALONNAGE HAZE 78
- Etal. Haze ok 78
- 5. Sélection des 80
- paramètres 80
- de l’instrument 80
- Menu SET UP 80
- 6. Indications pratiques 82
- concernant les 82
- mesures 82
- 8. Spécifications 87
- internationales 87
- 9. Description de 88
- l’interface 88
- 10. Données techniques 90
- 11. Sources d’erreur 92
- 12. Liste des 94
- composants et 94
- accessoires 94
- Riettometro 96
- No di cat. AG-4601 96
- 1. Descrizione Impianto 100
- 2. Avvio 101
- Verpackung mit Person 102
- Versione: 2.8 103
- 3. Funzionamento 105
- CALIBRAZIONE HAZE 108
- Calibrazione Haze ok 108
- 5. Selezionare i 110
- parametri dello 110
- strumento 110
- Menù SET UP 110
- Ausschnitt Sensor 111
- 6. Consigli pratici di 112
- misurazione 112
- AUTO-RANGE 113
- 8. Specicazioni 117
- Internazionali 117
- 9. Descrizione 118
- Interfaccia 118
- 10. Dati tecnici 120
- 11. Fonti di errore 122
- 12. Indice 124
- EG - Konformitätserklärung 125
- 228 012 718 EDFI 0811 128
Související produkty a manuály pro Měřící nástroje Altana Haze-Gloss Manual
(2 stránky)
(2 stránky)
Měřící nástroje Altana Wave-Scan II Uživatelský manuál
(188 stránky)
(188 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.032 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce